about us


feed pellet mill for making poultry farm feed, wood pellet mill for making biomass pellets,and chaff cutter for cutting straw and stalks

new article

new comment

new quote




08 | 2013/09 | 10
1 2 3 4 5 6 7
8 9 10 11 12 13 14
15 16 17 18 19 20 21
22 23 24 25 26 27 28
29 30 - - - - -

DATE: CATEGORY:feed pellet mill
poultry chicken feed pellet press machine

feed pellet press machine is widely used to make feed pellet for poultry, livestock, rabbit etc.

2.this pellet mill
 is adopted high-precision gear driven , advanced flexible coupling, for high productive efficiency .

3.The length can be adjusted by adjusting the tightness of the screws at the inlet of the machine.

4. Super quality bearing and oil seal to ensure high efficiency, stability and low noise.
The main spare part: Die and Roller

flat die pellet mill service life of the die and roller: 1000hours

Pellet density: 1100 -1200kg/m³

Heat value (wood pellet):4000-4500kcal/kg

Ash: 8%

Pellet moisture: 10%

Pellet diameter: 2-10mm

Pellet length: adjustable

DATE: CATEGORY:feed hammer mill
feed hammer mill design and structure
The design and placement of hammers is determined by operating parameters such as rotor speed, motor horsepower, and open area in the screen. Optimal
feed hammer mill design and placement will provide maximum contact with the feed ingredient. feed hammer mills in which the rotor speed is approximately 1,800 rpm, should be using hammers which are around 25cm  long, 6.35cm  wide, and 6.4mm  thick. For a rotor speed of about 3,600 rpm, hammers should be 15 to 20 cm  long, 5 cm  wide, and 6.4 mm  thick.
The number of hammers used for a feed hammer mill of 1,800 rpm, should be 1 for every 2.5 to 3.5 horsepower, and for 3,600 rpm, one for every 1 to 2 horsepower. Hammers should be balanced and arranged on the rods so that they do not trail one another. The distance between hammer and screen should be 12 to 14 mm for size reduction of cereal grains.
feed hammer mill Screen Design
The amount of open area in a  
diesel hammer mill screen determines the particle size and grinding efficiency. The screen must be designed to maintain its integrity and provide the greatest amount of open area. Screen openings (holes) that are aligned in a 60-degree staggered pattern optimize open area while maintaining screen strength. This method will result in a 40 percent open area using 3.2 mm (1/8 inch) holes aligned on 4.8 mm (3/16 inch) centers.
Feed producers need to pay particular attention to the ratio of open screen area to horsepower. Recommended ratio for grains would be 55 cm2 (~ 8-9 inches square) per horsepower (Bliss, 1990). Not enough open area per horsepower results in the generation of heat. When the heat generated exceeds 44C to 46C (120-125F), capacity may be decreased as much as 50 percent.
Application of
feed hammer mill
Poultry Feed, Cattle Feed, Shrimp Feed, Pig Feed, Fish Feed, Organic Fertilizer, All types of Grains, Bio Mass etc.
Sturdy & Robost construction.
Ratary Feeder can be attached for feeding & hammer mill motor can be synchronized with Feeder Motor.

DATE: CATEGORY:chaff cutter
This Hay Cutter/ Forage Chopper/Chaff Cutter is mainly used for cutting micro-green, dried corn stalks, rice straw and other forage crops, straw and so on, the family farmed cattle, sheep, horses, deer and other livestock, the ideal helper. 

the hay cutter has compact structure, small size, light weight; with steel structure, safe, reliable, single-phase power, easy to use, even long grass, and other characteristics suitable for green or dry chaff.
Structure of forage chopper :

1,The feeding part of the hay cutter: it is mainly made of feeding device, Tsao kun up and down, shim, set knife support seat.

2,The cutting part of the chaff cutter: moving blade, cutterhead, lock screw.

3,The driving mechanism: triangular belt, drive shaft, wheel gear, cardan joint

4, The running gear: caster wheel.

5, The protective device: protective cover

we also supply feed pellet mill,and feed grinder 

继续阅读 »

DATE: CATEGORY:chaff cutter
This chaff cutter machine is able to chop the corn stalks and grass into filamentous kneading fine feed. After chopping, the silage will be easy to bundling into round bales, so that to improve the efficiency of the fermentation decomposition of crude fiber, increase nutrition, and improve palatability.
1.Chaff cutter with Steel frame, small in size, light weight, convenient to remove

2.chaff cutter Design with safety device, avoid chew knife accident, the machine is safe and reliable.

3.Adopting advanced feeding provender device, unique feeding provender roller device (already obtained patent), the automatic feeding, conveying chain not winding grass, feed the grass is smooth, High production efficiency

we can also supply you feed pellet mill,fish feed pellet making machine   

copyright © 2019 wood pellet mill/feed pellet mill/chaff cutter all rights reserved.Powered by FC2 博客